tag: frame and panel

showing 1 - 20 of 38 posts matching box [X]
1 2 Next >

Sort By:

Æteriske Box

julienhardydesign, member | May 19th, 2013

Box of Philippino Toog with mobile compartment. Handcut dovetails and open slot mortise.Tung oil exterior finish, light lacquer inside. Inspired from a James Krenov piece. Made with...

view details

Easy handles for a sliding doors

AsaC, member | February 24th, 20137 comments

I like sliding doors and lids, partly because I get to make this nice handle in one simple step on the tablesaw.

view details

What hand tools can't you live without?

MPekovich, member | January 30th, 201364 comments

While building a travel tool chest I had to make a hard desicion about which hand tools would make the cut. I'll tell you what I settled on, but I want to know which tools would end up in your tool chest.

view details

Pennsylvania Spice Box

jlecomte, member | July 14th, 20122 comments

I made this Pennsylvania spice box from plans published in FW #196 by Steve Latta. I modified the feet (I did not like the original flat bracket feet and thus made ogee bracket feet) and the...

view details

Post and Beam Blanket Box

Eric.Mawby, member | April 16th, 20124 comments

I recently completed a blanket box for my daughter. This is actually the third I have made; one for each kid. It is my own “design,” if there is such a thing as designing a box. I refer...

view details

New Tool Box

zexelon, member | April 16th, 20123 comments

This project was borne out of a need to replace an aging tool box used to transport R/C Airplane tools. On the plus side it will also work well for anyone looking for a flexible tool box design. The...

view details

Ridiculously complicated boxes

gewima, member | August 24th, 20116 comments

I am trying to get better at joinery, but find just practicing on scrap is rather unfulfilling. I designed this box as an exercise in joinery. There is no other intended application, although I have...

view details

Half Size

MKConstruction, member | April 26th, 2011

This Model hapens to be half the size of my existing shop. I currently have a 24 x 40 shop/garage, but no where near the tools that I have placed in my dreamshop on here. If I ONLY had the money...

view details

My First Jewelery Box

arroff, member | February 9th, 20112 comments

No plans were used. I just new what I wanted it to look like. Solid mahogany except for the center cubby . It has maple sides and bottom. 3 drawers each side with a tilt out on each. Bifold...

view details

Cantilever Jewelry Box

roshie, member | November 21st, 20107 comments

This is my attempt at making a box float. I used a similar curve as seen in my Chou Chair design. I used a nice figured Western maple. Notice how I carried the figure from the lid right downnbspto...

view details

Tool Box : apprentice piece in oak

chopcatuk, member | September 24th, 20104 comments

Well if an architect can do an aprentice pieece at 50!. I based them (one for the Mrs and one for me) on the ubiquitous design with machine cut dovetails on the drawers. Oak and Maple with oil...

view details

Keeper Box

Sean_Thomas, member | August 4th, 20101 comment

I made this box for my friend's wife to house her collection of theraputic stones. The box is made primarily of walnut. The side, back panels and drawer fronts are veneered with a beautifully...

view details

Box made of Paduck

Graywoodworker1, member | April 30th, 20101 comment

We can manufacture custom Boxes carved and uncarved, Doors, Trim, Signs, Plaques, Tabletops and Panels, Pet ash repositories. Please e-mail me and provide any feedback you deem helpful...

view details

Cherry and Mahogany Valet Box

TerryFogarty, member | April 23rd, 2010

This valet was made from cherry and mahogany. I love the way these two similarly colored woods compliment each others reddish tones.This valet has corner posts and a raised panel in the center of the...

view details

Built-in Cherry Office - Desktop Organizers

jalambert, member | April 19th, 2010

One of pair of old-school desktop organziers. Part of a rear desk unit built in to a full floor matching home office in Brookline Ma. Cherry with padauk accents, hand-rubbed oil and wax finish...

view details

Natural Casket for "Green Burial"

Scummings, member | January 6th, 2010

This is one of the caskets that I designed and build for use in Natural Green Burial. All the wood is locally grown FSC certified Ponderosa Pine. I use no metal fasteners, just rely on...

view details

Dovetailed Walnut Keepsake Box

Jurgen01, member | December 2nd, 2009

This dovetailed walnut box was a gift to celebrate a neighbor's second child and presented as her baby's keepsake box. Generally inspired by early English arts and crafts designs, the shape and...

view details

"Deco"

Argyllshire, member | September 30th, 20095 comments

I designed this panel style box to express some of the Art Deco style.I wanted to make a box that was formal in design then shape it free form, a contradiction.

view details

Boxmakers Who Think Outside the Box

Tom, member | August 25th, 20091 comment

Check out boxes from around the globe at the Messler Gallery in Rockport, Maine

view details

Walnut & Bloodwood Necklace Chest

Jurgen01, member | August 11th, 20093 comments

Built to match a smaller jewelry chest of the same design and materials, this chest was made at the request of a client who wanted a larger chest made expressly for necklaces. The chest is made of...

view details

showing 1 - 20 of 38 posts
1 2 Next >