tag: accessory

showing 1 - 14 of 14 posts matching bent lamination [X]

Sort By:

My students works

YOUNGNICK, member | February 16th, 20123 comments

Hello everyone; I've been absent from these pages for a while as I've been shepherding my students here and I feel like a proud father. I'm showing off a selection of their work all designed and...

view details

Super bright LED floor standing light

Rich67, member | October 5th, 20112 comments

Hi Folks, I thought I'd share this. I bought some strips of super bright LED's to make a floor standing light with them. Mainly to use up some scraps I had and to be able to read during the winter...

view details

hall table

YOUNGNICK, member | June 1st, 20112 comments

A hall table veneered with macassar ebony and french polished. There is a central drawer made from ripple sycamore for the sides, base and back and Cameroon ebony ( jet black) for the front...

view details

Cantilever Jewelry Box

roshie, member | November 21st, 20107 comments

This is my attempt at making a box float. I used a similar curve as seen in my Chou Chair design. I used a nice figured Western maple. Notice how I carried the figure from the lid right downnbspto...

view details

Double Helix Plant Stand

mishad, member | November 12th, 20104 comments

This stand uses quartersawn white oak for the base and lacewood for the top, with holly inlay. The base is a bent laminate using spiral stair techniques and was done as part of a course at the Center...

view details

Dog House

kasenov, member | February 14th, 2010

This is a dog house I made as a wedding present for a couple of friends. They have traditional values/ stile and I tried to design it in a way to suit them, but also to reflect my own aestheticIt...

view details

Full Dress Aaron Burr Desk

btribble, member | May 15th, 20097 comments

Table/Desk Combination from an 19th Century design, dressed up with a little inlay.

view details

Shaker oval boxes and other furniture

Soltis, member | April 26th, 2009

Everything made is of Shaker inspired design. I have made many Shaker pieces over the years. Oval boxes are made of various domestic and exotic woods.

view details

Kathy's Cylinder Jewelry Box

BobEdenhofer, member | February 26th, 20092 comments

Jewelry Box made from Pommele Sapele & Bubinga veneer, black walnut, & Birdseye maple - silver gilded ends with a chemical patina. Cylinder design with 2 removable form fitted...

view details

Golden River Door and sidelight sculptures

ScottColorado, member | January 31st, 20092 comments

These projects are all my designs. My work is most defined by the "River Series" of inlaid resin, two shown here: Golden River Door and Entertainment Center with River Panel. In general I...

view details

Entertainment Center with River Panel

ScottColorado, member | January 18th, 200910 comments

The Entertainment Center is the center piece of this family's living room. Drawers are built to hold CDs and DVDs, family games, and more. The center river panel is inlayed dyed resin in...

view details

Monkey on a Motorscooter

vonschoenfeld, member | December 19th, 20081 comment

I created this for my sister who collects stuffed monkeys.

view details

Bubinga/White Oak bud vase/candle holder

Jaybird719, member | December 15th, 2008

Bent lamination of Bubinga & White Oak, supporting 3 small bud vases/candle holders.

view details

Tage Frid's Salad Tongs

just wanted to know, member | October 30th, 2008

Here is my take on Tage Frid's Salad Thong article in FWW. I used 2 pieces 3/32 Cherry that I re-sawed and planed up myself. To finish I used good old Mineral Oil and Bees Wax.

view details

showing 1 - 14 of 14 posts