 |
|
|
|
|
|
An Online Extra to Fine Woodworking Magazine
Micro-Adjustable Router Fence: parts list
A parts list for readers who want to build the fence described in Pat Warner's "Micro-Adjustable Router Fence" in the September/October 2000 issue of Fine Woodworking magazine.
The list is organized by supplier and includes part numbers.
From Reid Tool Supply (800-253-0421):
- Bronze bearing (5/16 in. ID x 3/8 in. OD x 3/4 in. length)
OIB-115
- 2 screws to hold aluminum in movable adjustment block (1/4-20 x 1 in.)
FCS-64
- 2 screws to affix movable block to carrier (5/16-18 x 1-1/2 in.)
FCS-84
- 2 screws to hold fixed block on base (5/16-18 x 1-1/2 in.)
FCS-84
- 2 screws to attach dial indicator holder to base (1/4-20 x 1-1/4 in.)
FCS-66
- 1 buttonhead screw to hold dial indicator (1/4-20 x 1 in.)
BHC-4050
- 2 screws to attach aluminum guides to base (1/4-20 x æ in. in.)
FCS-62
- 2 nylon washers for knob assembly
CT-533
- 1 flange nut for knob assembly (5/16- 18)
FNC-2
- 1 lock nut (5/16-18)
MHN-3320
- 6 in. of 5/16-18 all-thread
AMS-222 (or hardware store)
- 4 bolts to hold fence halves down (5/16-18 x 2-1/4)
FCS-90
- 1 flat foot stop and screw for dial indicator
JFF-19304
- 2 levers to clamp carrier to base (1/4-20)
KHB-255
- 2 flat feet washers for above levers
JFF-19304
- 1 dial indicator
SO-200-720
- 1 buttonhead cap screw to attach rule (8-32 x 5/8 in.)
BHC-4022
- 2 levers to clamp fence base to router table
KHB-16
- 2 flat feet washers for above levers
JFF-19305
- 2 studs for above levers (5/16-18 x 3 in.)
AMS-217
- Eight screws for fence faces to ash beams (1/4-20X1-1/2)
FCS-68
- 1 knob for spindle assembly
JCL-705
From Bruss Fasteners (800-536-0009):
- 4 Propell Nuts (T-nuts) for the larger clamp levers (5/16-18)
- 2 Propell Nuts (T-nuts) for smaller clamp levers (1/4-20)
From DeWalt (800-433-9258):
- DeWalt plastic vacuum fitting (1-1/2 in.)
328592-00
From L.S. Starrett (978-249-3551):
- 3-in. Starrett rule
C604R-3
Aluminum sources
www.metalmart.com (800-657-0721)
www.asapsource.com (734-213-ASAP)
www.use-enco.com (800-873-3626)
- Aluminum bars for guides and movable adjustment block
(20 in. of 1/4-in. by 1 in. stock, 6061 is a good standard grade)
- Aluminum for long washers
(21 in. of 3/8 in. by 1-1/4 in. stock, 6061 grade)
An online extra. If you encounter difficulty building this jig, you can email Pat Warner for advice at pat@patwarner.com. For the complete article, see FW #144.
|
|
|
|
