The Woodworking Life
End Grain Up Cork Bulletin Board
comments (0) September 30th, 2009 in blogs
Sean Melvin, Contributor
2 users recommend
The final product.
Following the publication of the "End Grain Up" article in issue 205, I set out to produce an eye-catching centerpiece for a project I'd been considering for quite some time. This cork board, born out of necessity, was really spiced up by a technique that brought life to an otherwise straightforward project.
The Cork Squares
I picked up a couple a couple of packages of cork squares at my local big-box, intent on making a bulletin board to tack up notes and other items. Each pack contained four squares, and as I lay them out to decide on the overall dimension of the board, I found that I could make a 3' x 3' square with a void in the center, using that void to display some sort of decorative wood square.
Centerpiece
Material
When I read through the "End Grain Up" article, I really liked the look of using the beauty of end grain, so I figured I would give this a shot as my decorative wood square. I had just finished up a project using plainsawn and quartersawn white oak, and had plenty of small scraps left over. I also had one medium sized piece of paduak that I had slowly been chipping away at with other small projects. I would use these two species for the board's centerpiece and frame.
Construction
- For the most part, I simply followed the directions and tips outlined in the "End Grain Up" article, albeit on a smaller scale. Here are a few notes concerning the end grain block construction:
• I spent a decent amount of time constructing a paper model that gave me a good idea of what size pieces I should cut and how I should orient them for a pleasing appearance.
• Because of the smaller end-grain slab that I was making, I found that my little block plane was very handy in preparing the sticks for glue up.
• After cross-cutting into end-grain sticks, I flipped and rotated every other stick to come up with a pattern that I liked.
• Taping the majority of the wood was a big time-saver when gluing up the end-grain sticks. It was hard enough planing the white oak and paduak end-grain block by hand without having bits of glue to worry about.
The Main Board
I used up the rest of my paduak for the frame, which surrounds a piece of particle board that makes up the main body of the bulletin board.
The frame's joints are simple miters, and I attached them with glue and a few finish nails to the particle board. The cork squares are only 3/16" thick, so to make the end grain block thicker and less fragile, I used a router to cut a recess in the particle board. This accommodated the extra thickness of the end grain block and still made everything flush on the surface.
Finishe
For the finish, I decided I'd use some boiled linseed oil I'd recently been given. Never having used it before, I was a bit heavy-handed with my application. It took six coats to get the look I was after but unfortunately, I was left with wood that was still tacky to the touch and not completely dry. In the end, I was forced to sand off the finish and apply an aerosolized oil-based varnish in three coats. This provided for a nice finish. In hindsight, the linseed oil could have worked, had I applied it in thin coats.
Second Time Around
If I were to build the bulletin board again, I would look into more options for the cork. We had bulletin boards in the dorms at UW-Platteville, and it was a full sheet of cork that was probably 7/16" to 1/2" thick. I noticed two things about the cork squares I purchased which were not ideal:
1. The thickness doesn't allow a standard tack to fully seat itself into the cork. Thicker cork would be more compatible with standard tacks.
2. I watched the squares curl up and down at the edges with swings in relative humidity, which accentuated the cracks between the squares. A full sheet of cork cut to fit the space in the bulletin board might function better and be more visually appealing.
Final Notes
The project was very economical; I used a lot of scrap wood and hardware that I had lying around. The only things I bought new were the cork squares, a 4' x 4' sheet of particle board, and a can of oil-based varnish. It was a fairly cheap way to try something new and broaden my skills as a woodworker.
posted in: blogs, white oak, paduak, end grain, bulletin board, tac board, end grain up, cork
ABOUT THE WOODWORKING LIFE
Get to know the woodworkers who make Fine Woodworking's online community the liveliest woodworking forum on the Web.
Each week, The Woodworking Life will feature the best projects, topical discussions, and how-to tips direct from the community.
WE WANT YOU! Find out how you can become a contributor to The Woodworking Life.
Looking for our archive?
Comments (0)
You must be logged in to post comments. Click here to login.