Reader's Gallery

showing 1 - 32 of 102 posts matching tool chest [X]
1 2 3 Next > Last

Sort By:

Hanging Tool Cabinet

Gerry4, member | October 20th, 20121 comment

This is a cabinet i built for my hand tools. The current project is giving me the details I need to complete the tool caddies and extra hanging surfaces I need. Thanks!

view details

Turn of the century cabinet makers tool chest.

toolchest, member | June 4th, 20126 comments

The first picture is an exterior shot showing the walnut , veneer, and dovetails I used to make the shell of the chest. About 220 dovetails went into making this chest. The inside of the chest lid...

view details

Cherry Tool cabinet

mouppe, member | May 31st, 20126 comments

I just completed this wall cabinet in which I intend my most special hand tools. It's made from solid cherry with a cherry plywood back, and cherry bookmatch veneered over plywood frame and panel...

view details

Tool Chest

neobassman, member | May 16th, 20124 comments

I needed a modest-sized tool chest to transport tools I will be using at a workshop this summer. I wanted something fairly compact, not a "master craftsman" chest (another project for another...

view details

Tool Box

D_Peet, member | February 15th, 20127 comments

Tool box is a box with a lot of tools in it. This is a box with all the tools organized in it. It nice to have alot of tools but a pain when you can't find them. In this box each tool has a place and...

view details

captain's chest

YOUNGNICK, member | August 11th, 20111 comment

A captains sea chest given a face-lift. It was intended for an 18 year old's birthday so the seaworthiness was not required , so no heavy lock, metal straps far too gothic and heavy carved initials...

view details

Some of my work done at North Bennet Street School

ACCustom, member | May 26th, 20113 comments

All work done while at North Bennet Street School to see more pics go to http://accustomfurniture.blogspot.com/

view details

Tools Cabinet

jvelez, member | February 15th, 2011

Nice tools cabinet made of Maple and Cedar. Assembly is dented for the case and drawers, no metals but the piano hinges and pulls. finish with oil Arm R Seal.

view details

Chisels's Rack

jvelez, member | February 15th, 2011

Rack Chisels made from Cedar, I made two since I'm going to get an other set of short chisels

view details

Hanging Tool Cabinet

Odrisan, member | January 21st, 20114 comments

As I've been using hand tools more and more, I found myself storing them all over my shop. Inspired by Henry Studley's famous tool cabinet (but nowhere near as good), and the numerous examples...

view details

Desk top tool chest

oakleafjoe, member | December 4th, 20104 comments

This is my second toolbox I have posted this year. My previous box I posted this spring. I wanted a small toolbox for my finer tools that would set on a desk or table. The top drawers are...

view details

grampa's tool box

MarkAReed, member | December 1st, 20103 comments

My Grandfather, Francis Townsend was an inspiration to me as I grew up. He was always working on one of his inventions in his shop when I came to visit. He would love to explain when I asked and...

view details

Tool Box

breaton, member | November 10th, 20105 comments

Here's a box I built thinking I'd put my small tools in it that had been collecting on the shelves. About half way through I found a small machinist's chest abandoned in the hallway and have...

view details

A Case for Apprenticeship

BetsyE, member | October 29th, 20102 comments

This tool chest by Trevor Hadden carries a legacy of craftsmanship. Hadden’s tutor was California furniture maker Michael Cullen, who based the program on his own training under...

view details

Tool Box : apprentice piece in oak

chopcatuk, member | September 24th, 20104 comments

Well if an architect can do an aprentice pieece at 50!. I based them (one for the Mrs and one for me) on the ubiquitous design with machine cut dovetails on the drawers. Oak and Maple with oil...

view details

Toolbox

oakleafjoe, member | April 24th, 201011 comments

This is my tool box I have been working on for close to 10 years now. I used mahogany curly maple, ebony, and reclaimed ivory. I used the brace handle as the handle for the drill box.

view details

Cherry Tool Cabinet

kingwah, member | February 28th, 20106 comments

Here is a version of the tool cabinet featured in a recent issue of Woodsmith. Mine is cherry. Finally a decent home for my handtools!

view details

Hanging Tool Chest

Jcumper, member | February 8th, 20107 comments

Made with Asian Lauan and Baltic Birch Plywood. It was my first and last experience with the Lauan; the veneer was only .015" thick, about the same as three thicknesses of tissue. Just one light pass...

view details

Mahogany Tool Chest

cliffwieser, member | January 6th, 20107 comments

This is a 28" x 14" x 18" tall machinist style tool chest. Drawers are finger jointed and run on Hard Maple runners. Drawers are HM also. Front panel reflects light wierd in the image, it looks...

view details

Curly Cherry toolchests

golfgloeckner, member | December 26th, 20099 comments

Pictured is one of two identical toolchests, built for Christmas gifts for my sons. The plans were Chris Gochnour's, in FWW #169. The cherry was not stained or dyed, but was sprayed...

view details

Blast Gate Improvement

MyCousinVinny, member | September 10th, 20097 comments

If you use these anoying Plastic gates that do not want to close. Check this out. I cut the corner and faced it down and it clears itself out............

view details

tool chest

GKL, member | July 10th, 20092 comments

Cherry, pine, and spalted alder tool chest

view details

Larry Gladstone's Tool Chest

LarryGladstone, member | June 29th, 20092 comments

Larry Gladstone's Tool Chest

view details

Chest with a workspace

bafaans, member | June 28th, 20094 comments

84L 36W 39H 13 Wood species used from local logger, Self Air dried, Salvaged stairs and pallets. 8 Months to complete. Demountable for easier transport.

view details

Down and Dirty in Plywood

Jeff_Richards, member | June 28th, 20095 comments

Constructed of plywood and scraps, storage in lid, trays in middle with pull-out (more storage below). Full extension drawer on bottom. Top once doubled as bench for planing etc.

view details

"New Yankee" toolchest

HersheyWoodworker, member | June 23rd, 20093 comments

I haven't seen this cabinet yet on FWW - and somebody had to put in a "shout out" to Norm! This cabinet was inspired by the New Yankee Workshop episode that also featured the Studley...

view details

Craftworker's Tool Chest

Landieman, member | June 20th, 20093 comments

This second attempt at chest making is a chest for my wife to store various craft items in. Made from New Zealand Silver Beech with drop down front and a Lacquer fiinish. The stainless...

view details

Machinist's Chest

Landieman, member | June 20th, 20094 comments

My first attempt at any sort of serious wood working project, this traditional drop front machinist's chest is made from recycled New Zealand Rimu, the front and back panel tongue and grooved board...

view details

Dad's apprenticeship toolchest

DaleSchack, member | June 20th, 20093 comments

My Dad apprenticed as a cabinetmaker in Denmark, and their second year project was a toolbox, which was then used for the rest of their apprenticeship and onwards in their careers as cabinetmakers...

view details

Toolbox for the Workshop

snapperhead, member | June 19th, 20094 comments

I needed a tool box in my workshop to hold all my carving tools and hand tools. I had tools in rolls, different cabinets and boxes. When I needed something it took time to find their...

view details

Whale Tail: Ash and Walnut Tool Chest with Spalted Maple side panels

AlecSebastian, member | June 18th, 20092 comments

This tool chest is made almost entirely from my stash of Treecycled lumber. The drawer fronts are resawn from 8/4 walnut stock to make two 3/4" fronts that match end to end. The topmost pair was then...

view details

bucket storage

oldpoopie, member | June 18th, 20094 comments

This is my air hose storage. I need to win the tablesaw to make one of those fancy toolboxes that everyone else has photos of! This allows you to hook the hose up thru the whip that sticks thru...

view details

showing 1 - 32 of 102 posts
1 2 3 Next > Last

Advertise here for as little as $50. Learn how

Welcome to Fine Woodworking's Readers Gallery,
an online photo community where woodworkers like you can share photos of all your woodworking projects. Log in or register now to create your public profile, share photos, and comment on other photos.

Check out our brand-new SHOP GALLERY and JIGS GALLERY. Get inspired and then post pictures of your own work.