Subscribe now and save up to 56%
Lumpy and thick. Paste wax tends to be thick and lumpy when first opened. It also tends to dry out a little when it sits unused for a while.
I’ve been using paste wax as the final polish on my furniture for years. I apply it with 0000 steel wool, let it sit, and then wipe it with a clean cotton rag to buff it out.
The first few times I used the product, it wasn’t so easy. The wax was often pretty stiff and tended to clump up on the applicator, making for a heavy application and thus a harder time removing it from the piece and buffing it after it sits.
The solution is to pour a small amount of mineral spirits onto the wax in the can. Typically a teaspoonful is enough, but you may need to add more if the wax is still lumpy or dry. Just don’t add so much that you end up with wax that’s the consistency of cake batter.
Dip the applicator in and lightly swirl the mineral spirits around. The wax will be thinned enough that it goes onto the applicator without clumps. This makes the wax go on smoothly and evenly. And best of all, it’s easier to wipe off and buff to a nice, soft sheen.
Smooth and thin. With a splash of mineral spirits, the wax gets thinned, making it easier to control the amount on the pad.
Wax on. A thin coat of wax goes on easily and more evenly after it's been thinned.
Wax off. The thinned application is also easier to buff out.
The perfect pair. Use mineral spirits to thin paste wax prior to application.
Get woodworking tips, expert advice and special offers in your inbox
Become a member today
Get instant access to all FineWoodworking.com content.
Subscribe to Fine Woodworking
Save up to 56%
Sorry. I accidentally posted my message before it was done... I built a bookcase about 25 years ago and I recently spruced up the finish. I cleaned and top-coated the shelves, the outside of the case, and face-frame. but not wanting to re-coat the insides, I just wanted to wax and rub out that part. I found it was horrible with dust nibs in the old poly finish. I had finished it in a dusty area, and I hadn't rubbed out the finish. (I hadn't even HEARD of rubbing out a finish back then.)I tried the wax and 0000 steel wool, but that process just took the peaks off. The finish now felt like it had a bad case of acne. So I put wax on a pad of 600 grit wet-or-dry sandpaper, lightly worked the nibs, and immediately wiped off the wax, and it was like glass! I worried the sheen would be different on the high spots, but not so. I didn't even need to add another coat of wax.
I have a bookcase that I made about 25 years ago. I REALLY
Hey treblecats, if you applied the solvent to the furniture and over the wax you diluted the wax and removed it. Check to see if your wax has a solvent in it (by the pic with the article one might assume that Johnson's contains mineral spirits). The article specifically said, "The solution is to pour a small amount of mineral spirits onto the wax in the can". Best of luck.
Help please! I didn't know about letting wax sit too long, so when I tried to buff it out with 0000 steel wool, it just got cloudy. So I put some linseed oil on it which looked good for about a day. Now, the cloudiness is back. What do I do now?
Good info, rmnbike. Thanks...
I believe that there are several wax brands (e.g., Briwax and others) which incorporate a solvent or two into the wax (or in some cases blend of waxes (caranuba, beeswax, etc.)to achieve the same effect. Many of these are also available tinted. I've used these, as well as the Johnson's and the (I forget the brand) bowling alley wax, and found that those that have the solvents mixed in are much easier to apply, and are almost liqui-gels at warmer temperature. It makes it easier to buff also, if you don't let it sit too long.
This week's prize is a 7-piece router bit set from Whiteside valued at $118!
Fast, fun approach to making a comfortable, casual seat
In this video Michael finishes the first of the three boxes. Gluing-up, planing, sanding and finishing bring a new piece of art to the world.
In this video Michael starts work on the second box, a carved and painted Saddle lid box.
Michael begins carving the saddle lid box with his ripple pattern along the top. Then turns to his 5/30 gouge to texture the sides of the box. This isn't work…
Become a member today and get instant access to all FineWoodworking.com content!
Plus tips, advice, and special offers from Fine Woodworking.
In-depth online classes from the experts at Fine Woodworking.
Enter now for your chance to win a Lee Valley block plane valued at $160.
© 2016 The Taunton Press, Inc. All rights reserved.
Become a member and get instant access to thousands of videos, how-tos, tool reviews, and design features.