Subscribe now and save up to 56%
The vertical dividers are great for sorting bills and coupons, stashing recipes, or for gathering phone messages until you can return a call. Few other projects work as hard and use so little wood. Most of the pieces are made from 1/2-in.-thick oak, with pine or poplar used as a secondary wood for the sides and back of the drawer. This organizer should take only two to three days to complete.
If you don’t have or can’t find a single board wide enough for the sides, glue up panels from narrower stock to make the sides, shelves, and dividers.
DOWNLOAD THE FREE PROJECT PLAN
Once you’ve mitered the top corner of each divider, smooth the cuts with a block plane. Clamp two boards together so that they remain identical.
Use a router to cut a 1/4-in.-high chamfer on the outside edges of the side panels.
Applying stain is easier before you assemble the case.
Plane down the top edge of the back piece so that it lies flush with the tops of the sides.
Before the glue dries, use a combination square to make sure the assembly is square.
To determine the proper size for the drawer front, butt the front against one drawer side, then mark the opposite end of the front.
Once all pieces are cut to length, use a compound miter saw or a tablesaw to nip one corner off both sides and the front top corner of the three vertical dividers. Then use a router to chamfer the outside edges of the side panels. Remember that the sides are mirror images, not identical. Establish a “right” and “left” side and chamfer only the top and two outside edges. One way to help remember the correct orientation is to tack the pieces together with double-sided tape.
You’ll find it a lot easier to finish the pieces now, before they are assembled into small shelves and tight compartments. If you want to darken the wood or even out different-colored boards, apply a stain followed by two coats of wipe-on varnish.
Install a dado set in the tablesaw and cut the 1/4 x 1/4-in. dadoes for the middle shelf. You can use the same setup to cut the 1/2-in.-wide dadoes for the bottom and top shelves and the rabbet for the bottom, by making multiple passes. Finally, lower the dado set to cut the 1/8-in.-deep grooves for the dividers.
Assemble the case Do a dry-fit to correct small mistakes, then proceed to the glue-up.
Glue the bottom and both shelves between the sides, gently clamp the case together, then slide in the back pane. Tighten the clamps, then check the assembly to be sure it’s square.
After about an hour, when the glue has dried, plane the top edge of the back piece so that it lies flush with the sides. If necessary, trim the tops of the dividers before they’re glued in place. Once everything fits, apply glue to the grooves in the back and top shelf, then slide the vertical dividers in place.
Building the drawerThe drawer is a rabbeted and dadoed box with a false front glued on. If you prefer something easier, you can make a serviceable drawer by butt-joining the front and back to the sides. Since the bottom is glued in place, a little glue and bamboo skewers on the corners are enough to hold the drawer together. In either case, the dimensions on the cutlist and plan are only a guide. The goal is to fit the drawer to the case, not to make cuts just because a cutlist tells you to.
Using the organizer as your guide to the proper dimensions, rip stock for the front, back, and sides. Test the fit against the case and size it so that the stock slides smoothly into the drawer cavity.
On the front and sides, cut a 1/8-in-deep groove to house the drawer bottom. Instead of grooving the back, raise the blade and trim away the groove completely. Then crosscut the sides so that they are 1/4-in. shorter than the depth of the drawer opening.
Place a single side piece into the opening and use it as a spacer to determine the length of the front and back pieces. Set the drawer front in place and make a small mark with a knife or sharp pencil. After cutting the rabbets (in the front) and dadoes (in the back) on the sides, the front will fit in the opening. As you crosscut the front and back pieces, cut it a hair short. That way, the drawer will have a little room to move from side to side.
Use a marking gauge to transfer the thickness of the drawer front to the front inside face of one of the drawer sides. Adjust the tablesaw to make a 1/8-in.-deep cut and adjust the rip fence so that the blade is cutting along the inside front face of the drawer side. It may take two to three passes to nibble up to the end of the board, but this is faster than switching to a dado cutter. Repeat this cut on the inside front end of the other side piece.
To cut the dado to house the back of the drawer, adjust the fence so that there is 1/4 in. between the fence and the blade, then pass the stock across the blade and make the mirror cut in the other side piece. Move the fence another 1/8 in. away from the blade and take another pass. Sneak up on the proper fit slowly by making small adjustments to the fence.
Dry-fit the drawer sides, front, and back, then measure the dimension of the bottom panel and cut it to fit.
Assemble the drawer Apply glue to the corners and bottom grooves, then reassemble the drawer and check for square.
To provide extra reinforcement, “nail” each corner with bamboo skewers. Drill three 1/2-in.-deep holes at each corner, apply glue to the skewer, and lightly tap it into place. When dry, trim the skewer flush to the side with a small saw or chisel.
Find the center of the drawer front and drill a pilot hole for the knob. Then cut the false front to the exact size of the drawer opening. Attach the false front to the drawer, then drill from the back of the drawer front through the false front. Attach the knob.
Finishing Apply a final coat of varnish to all exterior surfaces. Because you’ve prefinished all the parts, focus only on the outermost surfaces. Don’t worry if you can’t reach into all of the narrow drawers and compartments. Wait a day or so, then apply a little paste wax with a small scrap of abrasive pad. As a nice final touch, line the drawer bottom with felt, glued to a piece of cardboard that’s the same size as the drawer bottom.
Excerpted from:Furniture You Can Buildby Joseph Hurst-Wajszczuk
The projects in this book are designed to help you improve your skills while enjoying time in your shop.
Buy the book or purchase individual chapters for download
Browse all books and DVDs
Get woodworking tips, expert advice and special offers in your inbox
Become a member today
Get instant access to all FineWoodworking.com content.
Subscribe to Fine Woodworking
Save up to 56%
Tom’s cabinet blunder and other smooth moves. Plus we roll out some new segments: stats and surprise questions. Will they make the cut?
Seamless boxes from a single block of wood
Creating loose, unregulated appearances with gouges
Discover the beautifully carved and painted details of Michael Cullen's bandsawn boxes
Basic dovetailed project is loaded with character
Become a member today and get instant access to all FineWoodworking.com content!
Plus tips, advice, and special offers from Fine Woodworking.
In-depth online classes from the experts at Fine Woodworking.
Enter now for your chance to win a Lee Valley block plane valued at $160.
© 2016 The Taunton Press, Inc. All rights reserved.
Become a member and get instant access to thousands of videos, how-tos, tool reviews, and design features.